一、概述
河南邦信外加電流陰極保護恒電位儀通過參比電極測量通電點電位，作為取樣信號與控制信號進行比較，實現控制并調節極化電流輸出，使通電點電位得以保持在設定的控制電位上。邦信恒電位儀主要用于在電極過程動力學、電分析、電解、電鍍、金屬相分析，金屬腐蝕速度測量和各種腐蝕與防腐研究以及電化學保護參數測試。
二、技術參數
l 輸入電壓：AC 380V或者AV 220V
l 頻率：50HZ
l 輸出電流：直流（0-75A）
l 輸出電壓：直流（0-75V）
l 電位范圍：直流0-3000mV
l 溫度范圍：-20~+55℃
l 防護等級：IP20
l 恒電位跟蹤精度：≤ 5mV
l 恒電流精度： ≤ ± 2 ％
l 紋波系數： ≤ 5 ％
一、操作說明
1、預熱：接通電源，預熱15分鐘，以使儀器工作在穩定狀態。
2、校準：指電流表零點校正。接通電源，預熱15分鐘后，按下“校準”鍵(11)，“通一斷”開關(13)置于“斷”的位置，電流量程(2)置于2mA檔，如電流表(3)顯示不為0.000可調節前面板上的“調零”鍵(12)，使電流表顯示為0.000。
3、電極開路電位測量：即研究電極自然腐蝕電位測量，將電極輸入(1)的引線連接到電解池體系，“通-斷”開關(13)置于“斷”位，接通電源(14)，打開電源開關(15)，預熱15分鐘后按下“恒電位”鍵(8)，電流鍵(11)，“參比”鍵(5)，數字表(4)顯示即為參比電極相對于研究電極的開路電位，即研究電極的自然腐蝕電位，但符號相反。
4、恒電位極化測量：按照上述第3項完成自然腐蝕電位測量后，接著按下“給定”鍵(5)，此時數字表(4)顯示的給定電位值，調節恒電位給定電位之粗調鍵(6)和細調鍵(7)，使數字表(4)顯示給定電位值，與自然腐蝕電位值相等。“通-斷”關開(13)置于“通”的位置，此時輔助電極的電路接通，儀器開始實施恒電位運作，現在便可進行以自然腐蝕電位為起點的恒電位極化測量。
